Author: Fiber-MART.COM

eShop of Fiber Optic Network, Fiber Cables & Tools

Customized 40G QSFP+ to 8 LC AOC Breakout Cable

Bandwidth usage is soaring, driven by the proliferation of Internet-connected devices.  In this article, some knowledge of 40G QSFP+ to 8 LC AOC Breakout Cables will be provided.

Bandwidth usage is soaring, driven by the proliferation of Internet-connected devices.  In this article, some knowledge of 40G QSFP+ to 8 LC AOC Breakout Cables will be provided.

 

40G QSFP+ to 8 LC AOC Specifications

40GBASE QSFP+ to eight LC/SC/ST/FC Connector Breakout Active Optical Cable are a high performance, low power consumption, long reach interconnect solution supporting 40G Ethernet, fiber channel and PCIe. It is compliant with the QSFP MSA and IEEE P802.3ba 40GBASE-SR4. QSFP+ Breakout Cable is an assembly of 4 full-duplex lanes, where each lane is capable of transmitting data at rates up to 10Gb/s, providing an aggregated rate of 40Gb/s. QSFP+ Breakout Cable are suitable for short distances and offer a highly cost-effective way to connect within racks and across adjacent racks. This product is a high data rate parallel active optical cable (AOC), to overcome the bandwidth limitation of traditional copper cable. Consequently, an aggregate data rate of 40Gbps over 100 meters transmission can be achieved by this product, to support the ultra-fast computing data exchange.

65.jpg

All our 40GBASE QSFP+ to LC/SC/ST/FC Connector(8) Breakout Active Optical Cable are 100% compatible with major brands like Cisco, Juniper, Enterasys, Extreme, H3C and so on.

 

QSFP-8X-AOC-1

  • Connector 1: QSFP+
  • Connector 2: 8 x LC/SC/ST/FC Connector
  • Length: 1 meter
  • Cable Type: AOC Cable
  • Full duplex 4 channel 850nm parallel active optical cable
  • Transmission data rate up to 10.3Gbit/s per channel
  • SFF-8436 QSFP+ compliant housing and hot pluggable electrical interface.
  • Management Interface and digital diagnostic monitoring(DDM) through I2C
  • Support Rx output pre-emphasis
  • 4ch 850nm VCSEL array
  • 4ch PIN photo detector array
  • Helix type multi-mode optical fibre cable of up to 100m
  • OFNP (Optical Fibre Non-Conductive Plenum) rated cable
  • Differential AC-coupled high speed data interface
  • Housing isolated from connector ground
  • Operating Temperature: 0 to 70℃
  • RoHS 6 compliant
  • 3V power supply voltage

Applications

  • Infiniband transmission at 4ch SDR(2.5Gbit/s), DDR(5Gbit/s) and QDR(10Gbit/s)
  • Multi-channel 10Gb Ethernet transmission up to 4 channels
  • Fiber Channel transmission at 8.5Gbit/s per channel, up to 4 channels
  • QSFP+ to LC/SC/ST/FC cables with MT connectors for plugging into existing cable runs or patch pannels
  • Creating a breakout cable with four Duplex LC connectors for port expander applications
  • SDR /DDR /QDR
  • Data Centers

Conclusion

Along with the popularity of 40G Ethernet, the market of 40G QSFP+ AOC cable has been growing over the years. It is definitely a better choice for high speed transmission over short distances. If you would like to order high quality compatible 40GBASE QSFP+ to LC/SC/ST/FC Connector(8) Breakout Active Optical Cable and get worldwide delivery, we believe Fiber-mart.COM is your best choice.any question pls feel free to contact me at service@fiber-mart.com

Difference Between Tight-Buffered Breakout and Distribution Cables

There are two basic styles of fiber optic cable construction: loose tube and tight buffered. Tight buffered cables provide improved reliability and quick termination for today’s cable installation systems.

There are two basic styles of fiber optic cable construction: loose tube and tight buffered. Tight buffered cables provide improved reliability and quick termination for today’s cable installation systems. Tight-buffered breakout cables and distribution cables are two main types of the tight-buffered cables.loose tube cables hold more than one optical fiber, each individually sleeved core is bundled loosely within an all-encompassing outer jacket. However, in tight buffered cables, there are not so many cables as loose tube cables.

 

Cable Structures

Breakout Cable Structure

Breakout cable is also known as fan-out cable. As the following picture shows, breakout cable consists two or more simplex cables bundled around a central strength member. Each fiber has its own jacket and all of the fibers are packaged together inside the same outer jacket. Thus, breakout cable can also be broken out into individual simplex cables for separate use when running through walls of a building. Breakout cable is usually designed with tight buffer and the fiber counts are varied from 2 to 24 fibers.

图片1.png

 

 

 

Distribution Cable Structure

 

Unlike the breakout cable, distribution cable is smaller in size and lighter in weight. Fiber counts of distribution cable can be more intensive than the breakout cable for up to 144 fibers. Many fibers may not be used immediately but can be left for future expansion. Although the distribution cable has a more compact design, the tight-buffered fibers inside the cable are only bundled in a single outer jacket for protection, as shown in the picture below. Yet this has made the distribution cable to be easily handled and stripped for field termination.

 

图片2.png

 

Conclusion

Tight-buffered cables are optimal for indoor applications. With the design of armored layer, they are also used for indoor/outdoor applications. Fiber-Mart provides a wide range of quality optical fiber cables with detailed specifications displayed for your convenient selecting. Per foot price of each fiber cable is flexible depending on the quantities of your order, making your cost of large order unexpected lower. Customers can also have the flexibility to custom the cable plant to best fit their needs.any question pls feel free to contact me at service@fiber-mart.com

The Advantages of CATV EDFA

Optical amplifiers serve as an integrated part of long haul data transmission. Fiber optical transponders and fiber optical amplifier are used in the WDM fiber optic system, and it makes WDM transmission possible.

Optical amplifiers serve as an integrated part of long haul data transmission. Fiber optical transponders and fiber optical amplifier are used in the WDM fiber optic system, and it makes WDM transmission possible. In recent years,fiber optic CATV EDFA System especially 1500nm optical fiber CATV System is being rapidly develop in our country.

What is EDFA?

Erbium Doped Fiber Amplifier is short for EDFA,which was applied in 90 s in the optical fiber transmission system and its popularization and application of optical fiber communication technology has brought a revolution.EDFA is in small volume,low power consumption,easy to us.What’s more,it is convenient to install all kinds of application systems,such as SDH frame inside,CATV machine box, DWDM system frame.as one of a functional modes of the Optical fiber amplifier system,there are generally two kinds of methods to insert the network management system.One is 232 c interface circuit with optical fiber amplifier to transfer parameters of the optical fiber amplifier and alarm information to the network management system,unified management,display and disposal.

An EDFA is an optical amplifier based on Erbium-doped optical fiber, that amplifies optical signals without converting them into electrical form. EDFAs use semiconductor lasers to pump Erbium Doped Fiber to amplify light in 1.5 μm wavelength region where telecom fibers have their loss minimum. It has low noise and can amplify many wavelengths simultaneously, which makes DWDM possible and becomes a key enabling technology for optical communication networks. Since the realization of EDFA, it has developed rapidly and has become the amplifier choice for most applications in optical communication.

f0d6e8c5027c66ab48727b0cf3b882d1.image.500x500.jpg

Advantages of CATV EDFA

EDFA is in the low noise,has the characteristics of good gain trace,large amplifier bandwidth,compatible with wavelength division multiplexing (WDM) systems,with high efficiency,work performance is stable,mature technology and so on and so forth.It is very popular in the modern long-distance high-speed optical communication system.

◆ Good character：

Before the pump generally use 980 nm,after level pump use 1480 nm.Minimizing the NF of EDFA by reasonable optimization to make the system access excellent CNR.

◆ Reliability：

Use 1 u 19 “standard rack, built-in high-performance switching power supply.It can work in 85∽265 vac enterprise voltage.DC48V power supply (reservations) can be an option,too.Chassis cooling can be automatic temperature control.

◆ Intuition：

This machine contains a microprocessor to monitor the working state of the pump laser, LCD displays the working parameters.

◆ Network management model：

Options type monitoring transponder to ensure to meet the national standard with the SCTE HMS standards, which can realize network management monitoring.

◆ Adjustable output optical power：

Output optical power can be changed to -3dB.

◆ The power plug type：

Aluminum structure plug type switching power supply.Be good for heat dissipation and replacement.

 

Conclusion

The most prominent feature of optical amplifier is that the device can amplify optical signal directly without the need to convert the signal into an electrical one before amplifying. EDFA (Erbium-doped Fiber Amplifier) is the one type of many different optical amplifiers that can achieve signal amplification over long-hual optical communication. Fiber-MART provides broad optical amplification solutions for different applications, from telecom, datacom to CATV and has strong technology and experience to design and manufacture EDFA, EYDFA, Raman and Raman-EDFA hybrid. You can save cost by using the most efficient Fiber-Mart CWDM & DWDM Networks solutions. Pls feel free to contact me at service@fiber-mart.com

SDH SONET 10GBASE SFP+ 1310nm 10km Transceiver

SSFP-10G31-10

Fiber-Mart SDH SFP+ transceiver is a high performance, cost effective modulse for serial optical data communications applications specified for signal rates of 9.95 Gb/s to 11.1 Gb/s. The modules are designed for single mode fiber and operates at a nominal wavelength of 850nm/1310nm/1550nm. The transmitter section incorporates uncooled directly modulated 1310nm distributed feedback laser (DFB) or EML colled laser 1550nm. The receiver section uses PIN photodetector for low dark current and excellent responsivity or APD high sensetivity receiver. CDR chipset is integrated both to transmitter TX and receiver RX side.

Key Features

    • Supports 9.95Gb/s to 11.1Gb/s bit rates
    • Average Output Power:-6~-1dBm
    • Receiver Sensitivity: -14.4dBm
    • SFP 10G with CDR both at TX and RX side
    • IEC 60825-1 Class 1/CDRH Class 1 laser eye safety.
    • Hot-pluggable SFP+ footprint
    • 10km at 1310nm DFB/PIN Transmitter
    • Duplex LC connector
    • Low Power dissipation
    • Superior Thermal and EMI integrity performance to support high port densities
    • LC Duplex optical connector interface conforming to ANSI TIA/EIA604-10 (FOCIS 10)
    • Built-in digital diagnostic functions, DDMI
    • RoHS-6, CE, FDA, FCC, TUV, UL certifactes

 

Applications

    • 1000BASE-SX 1G Ethernet
    • 1000BASE-LX 1G Ethernet
    • 10GBASE-SR/SW 10G Ethernet
    • 10GBASE-LR 10G Ethernet

 

Ordering Information

Part No. Data Rate (Gbps) Wavelength (nm) TX Power (dBm) Re Sens. (dBm) Transmission Distance Fiber Type Connector Type Temp. Range Digital Diagnostics
SSFP-10G85-3M 9.95~10.3G 850 -6~-1 ﹤-11.1 300m MMF LC Com./Ex./Ind. Yes
SSFP-10G31-2M 9.95~10.3G 1310 -6.5~-0.5 ﹤-10 220m MMF LC Com./Ex./Ind. Yes
SSFP-10G31-2 9.95~10.3G 1310 -6~-1 ﹤-14.4 2km MMF LC Com./Ex./Ind. Yes
SSFP-10G31-10 9.95~11.1G 1310 -6~-1 ﹤-14.4 10km SMF LC 0~70℃ Yes
SSFP-10G31-20 9.95~11.1G 1310 -3~-1 ﹤-14.4 20km SMF LC 0~70℃ Yes
SSFP-10G31-40 9.95~11.1G 1310 -3~-1 ﹤-14.4 40km SMF LC 0~70℃ Yes
SSFP-10G31-70 9.95~11.1G 1310 2~5 ﹤-20 70km SMF LC 0~70℃ Yes
SSFP-10G55-40 9.95~11.1G 1550 -4.7~4 ﹤-15.8 40km SMF LC 0~70℃ Yes
SSFP-10G55-80 9.95~11.1G 1550 0~5 ﹤-23 80km SMF LC 0~70℃ Yes

 

Packaging

    • Antistatic bag
    • Packed on pallets in a box(Default Customer Options)
    • Specific Labels as Request
    • Seperate white Box for each transceiver

 

OEM and ODM

Combining our extensive design and engineering capability in optical transceiver industry, with our competitive advantages from integrated manufacturing capability, internal supply chain, and cost competitive and scalable operation infrastructure, Fiber-Mart provides OEM, ODM, and contract manufacturing service to world leading customers with our manufacturing facilities in China.We are also mainly engaged in providing complete sets of optoelectronic device solutions to gain more brand extensions and influence for Fiber-Mart in the world.

  • OEM/ODM order is available
  • We can supply SSFP-10G31-10 according to your requirements, and design SSFP-10G31-10 label and packaging for your company. We welcome any inquiry for customized SDH SONET SFP+ optical transceiver.

100GBASE-LR4 and OTN Dual Rate CFP 1310nm 10km Transceiver for SMF

CFP-100GT31-10

Fiber-MART.Com’s CFP-100GT31-10 100GE CFP module offer customers 100 Gigabit Ethernet connectivity options for data center networking, enterprise core aggregation, and service provider transport applications.The module supports a link length of 10 kilometers on standard single-mode fiber (SMF, G.652). They are compliant with the CFP MSA, IEEE 802.3ba 100GBASE-LR4 and OTU4 4I1-9D1F requirements specified in ITU-T Recommendations G.959.1/G.709 and Supplement 39 (G.sup39).100 Gigabit Ethernet signal is carried over four wavelengths. Multiplexing and demultiplexing of the four wavelengths are managed within the device.100GBASE-LR4 CFP form factor transceiver module for SMF, 4 LAN-WDM lanes in the 1310nm wavelength window, LC duplex connector with up to 10km reach per IEEE 802.3ba requirements.

Key Feature

    • Hot-pluggable CFP form factor
    • Supports 103.1Gb/s and 112Gb/s aggregate bit rate
    • Power dissipation <16W
    • RoHS-6 compliant (lead-free)
    • Single 3.3V power supply
    • Maximum link length of 10km on Single Mode Fiber (SMF)
    • 4x25Gb/s DFB-based LAN-WDM transmitter
    • 10x10G MLD electrical interface
    • Duplex SC or LC receptacles
    • MDIO management interface
    • Commercial case temperature: 0°C to 70°C

 

Applications

    • OTN OTU4 4I1-9D1F
    • 100GBASE-LR4 100G Ethernet
    • Datacom/Telecom switch & router connections
    • Data aggregation and backplane applications
    • Proprietary protocol and density application

 

Packaging

    • Antistatic bag
    • Packed on pallets in a box(Default Customer Options)
    • Specific Labels as Request
    • Seperate white Box for each transceiver

 

OEM and ODM

Combining our extensive design and engineering capability in optical transceiver industry, with our competitive advantages from integrated manufacturing capability, internal supply chain, and cost competitive and scalable operation infrastructure, Fiber-Mart provides OEM, ODM, and contract manufacturing service to world leading customers with our manufacturing facilities in China.We are also mainly engaged in providing complete sets of optoelectronic device solutions to gain more brand extensions and influence for Fiber-Mart in the world.

  • OEM/ODM order is available
  • We can supply CFP-100G31-10 according to your requirements, and design CFP-100G31-10 label and packaging for your company. We welcome any inquiry for customized 100G optical transceiver.

100GBASE-SR10 CXP 850nm 150m Transceiver for MMF

CXP-100G85-1M

100GBASE-SR10 CXP form factor transceiver module for multi mode fiber, short wavelength over 10 lanes, in the 850nm wavelength window, MPO/MTP connector with up to 100m on OM3 and 150m on OM4 reach per IEEE 802.3ba requirements. 100GBASE-SR10 CXP transceiver modules are designed for use in up to 100 Gigabit per second links over multimode fiber. They are compliant with the CXP Specification and CPPI interfaces.

Key Feature

 

  • Hot Pluggable CXP footprint
  • 1.06Gb/s to 10.5Gb/s per channel
  • Short wavelength over 10 lanes, 840 to 850nm
  • VCSEL array transmitter and PIN array receiver
  • Up to 100m on OM3 and 150m on OM4 MMF
  • Utilizes a standard MPO/MTP Connector
  • Unretimed CPPI electrical interface
  • Requires 3.3V power supply only
  • Low power dissipation: <3.5W
  • Operating case temperature: 0°C to +70°C
  • Built-in digital diagnostic functions

 

 

Applications

 

  • Data center
  • 100GBASE-SR10 100G Ethernet
  • Multiple 4G/8G/10G Fibre Channel

 

 

Ordering Information

Part No. Data Rate (Gbps) Wavelength (nm) Transmission Distance Fiber Type Connector Type Temp. Range Digital Diagnostics
CXP-100G31-1M 105G 850nm 100m(OM3) MMF MPO/MTP 0~70 Yes
CFP-100G85-1M 103G Ten lanes 840 to 860 100m(OM3)
150m(OM4)		 MMF MPO/MTP 0~70 Yes
CFP-100G31-10 103G Four lanes:
1295.6, 1300.1, 1304.6, 1309.1		 10km SMF LC 0~70 Yes

Notes

  • xx means compatible brand. (For example: CO= Cisco, JU=Juniper, FD=Foundry, EX=Extreme, NE=Netgear,etc.)

 

 

Packaging

 

  • Antistatic bag
  • Packed on pallets in a box(Default Customer Options)
  • Specific Labels as Request
  • Seperate white Box for each transceiver

 

 

OEM and ODM

Combining our extensive design and engineering capability in optical transceiver industry, with our competitive advantages from integrated manufacturing capability, internal supply chain, and cost competitive and scalable operation infrastructure, Fiber-Mart provides OEM, ODM, and contract manufacturing service to world leading customers with our manufacturing facilities in China.We are also mainly engaged in providing complete sets of optoelectronic device solutions to gain more brand extensions and influence for Fiber-Mart in the world.

  • OEM/ODM order is available
  • We can supply CXP-100G85-1M according to your requirements, and design CXP-100G85-1M label and packaging for your company. We welcome any inquiry for customized 100G optical transceiver.